Innovative Heat Treatment – RAPTOR is a heat treatment Stud Welder designed to work in conjunction with the standard heat treatment equipment.
The Raptor Stud Gun can be used as a separate modular unit or can be built into bespoke heat treatment unit.
The Raptor auto pin welder is a capacitance-discharge welding unit intended for general purpose attachment of pins and wires to work pieces. It has variable energy output to suit a range of pin or wire sizes. The Raptor auto pin welder is powered by a rechargeable battery or by connection to a 110V a.c. supply (or optional 230V a.c. supply).
| Supply Voltage: | 110 V.a.c. 50/60Hz |
| Battery: | Sealed lead-acid (non-spillable) 12 VOLT, 2.1Ah |
| Weld Voltage: | 42 to 62V |
| Ready to weld charging time: | 6s to 60J 20s to 250J |
|
Number of welds : (from fully charged battery) |
800 welds at 40 joules |
| Maximum battery recharge time: | 6 hours |
| Dimensions: |
METRIC (225mm x 230mm x 310mm ) IMPERIAL (. 8.8" x 9" x 12.2" ) |
| Weight : | 10 kg |
| Design Standards: |
EMC: EN61000-6-1:2001, EN61000-6-3:2001. LVD: EN 61010-1: 2001 |
NOTES:
1. BATTERY – (longer recharge time THEN SIX HOUR can degrade the battery)
2. SUPPLY VOLTAGE – OPTIONAL– IS AVAILABLE IN 230 VAC )
3 . Safety Safety – glasses should be worn by the operator.
THE RAPTOR-PIN WELDER was desined specifically for the Industrial Heat Treatment industry. Ideal for attaching thermal insulation pins to a workpiece where not practical to use banding wire or steel tape. It can also be used to attach thermocouple wire when set in lower output energy range.
Operation-Select required output energy then switch unit On. The unit will charge up until ‘Ready’ to weld. With the welding return magnet attached to the workpiece, the wire or pin to be welded is then held by the supplied pliers and touched against the workpiece at the required point. Once this contact is made between the wire or pin and the workpiece the unit automatically spot welds the pin or wire to the workpiece. Three short audible beeps followed by one longer beep indicates that the unit is about to discharge and make the spot weld. The unit will then automatically recharge ready for the next spot weld. If the unit is left unused for approximately 5 minutes, it will go into ‘sleep’ mode (indicators off). Switching the unit Off then On again will reactivate the unit.
Hand free operation with audible count-in to ‘auto-weld’ .
Two energy ranges selectable: 30 to 60 Joules or 125 to 250 Joules .
Rechargeable battery.
Low battery LED indicator and auto switch-off to conserve battery.
Strong-Durable Case floor standing unit with hard rubber feet and tool storage tray
Supplied with:
> 2 meter (78″) welding cables,
> Welding Return magnet,
> Supply Lead,
> Interchangeable pliers
| Catalog # | Description: | |||
|
|
10700 | RAPTOR-PIN WELDER PORTABLE, BENCH TOP PIN WELDER |
|
|
|
10703 | 110 VOLT POWER SUPPLY 3' IN LENGHT |
|
|
|
10704 | WELDING CABLE 6.5' IN LENGHT |
|
|
|
10705 | MAGNET CABLE 6.5' IN LENGHT W/ DINSE CONNECTIONS LEADS |
|
|
|
10706 | GROUND CABLE W/ CLAMP 6.5' IN LENGHT W/ DINSE CONNECTIONS LEADS |
|
|
|
10707 | 3" MILD COOPER PINS |
|
|
|
10708 |
2.5" 12 GA Mild Steel Square Washer (Comes in 1000 per box) |
|
|
|
10709 |
1.5" 12 GA Mild Steel Round Washer (Comes in 1000 per box) |
|
|
|
10712 |
3" 12 GA Stainless Steel
Pins (Comes in 1000 per box) |
|
|
|
10810 |
3" 12 GA Mild Steel Pins (Comes in 1000 per box) |
|
|
|
10711 | 12GA #4, Collett |
|
|
| Catalog # | Description: | |||
|
|
10700 | RAPTOR-PIN WELDER PORTABLE, BENCH TOP PIN WELDER |
|
|
|
|
10703 | 110 VOLT POWER SUPPLY 3' IN LENGHT |
|
|
|
|
10704 | WELDING CABLE 6.5' IN LENGHT |
|
|
|
|
10705 | MAGNET CABLE 6.5' IN LENGHT W/ DINSE CONNECTIONS LEADS |
|
|
|
|
10706 | GROUND CABLE W/ CLAMP 6.5' IN LENGHT W/ DINSE CONNECTIONS LEADS |
|
|
|
|
10707 | 3" MILD COOPER PINS |
|
|
The cup head weld pin welder application features
1. They are widely apply for anywhere need to install insulation material.
2. Reduce the install steps and time, no any requirement for the surface.
3. Save time for install the insulation material.
4. Fix the insulation material securely after the cup head pin is welded.
5. No limit for place for install insulation material, whatever it is flat or round or square.
6. The welding will not be limited by the temperature. The weather will not effect the installing.
7. Reduce the installation time, we can weld the cup head weld pins at same time during install the insulation material.
Leave the application on our website or by phone
The manager will contact you for further details
We will gladly deliver your order soon
